Home > Cisco Error > Cisco Error No Memory Detected Aborting

Cisco Error No Memory Detected Aborting

Recommended Action Correct the specified condition or the router may shut itself down or fail to operate properly. Error Message %ARAP-4-GETBUFFER: MSG_TRACEBACK getbuffer failed: size [dec]: [chars] Explanation ARAP could not obtain a buffer for an incoming packet. Error Message %AT-3-NOBESTPATH: Could not compute best path for network [atalk_net] Explanation A path to the specified network could not be found. Otherwise, you must split your AppleTalk network into smaller networks. have a peek here

Error Message %CBUS-3-CORRUPT: Controller [dec], wrote [hex], read [hex], loc [hex] - dci_memtest() Explanation A hardware component failed an internal diagnostic test. Recommended Action This router will restart AppleTalk processing on the common network interface to resolve the address conflict. Recommended Action Issue a clear interface command. Recommended Action Call your technical support representative for assistance. https://supportforums.cisco.com/discussion/10474611/error-no-system-memory-detected-cisco-1721

Error Message %CBUS-3-CCBREPLY: [chars]: bad CCB reply [hex] Explanation A hardware or software error occurred. Error Message %BRI-3-ODDSTART: Interface [chars] Explanation An internal software error occurred. Recommended Action Examine this router to see why it closed this connection with this peer. Recommended Action Report this message to your technical support representative.

Error Message %CBUS-3-MEC_OUTHUNG: Interface [chars] output hung, [hex], [chars], [chars] Explanation Output hung on a ciscoBus Ethernet interface. For Example Latest 2800 IOS c2800nm-adventerprisek9-mz.124-25b.bin size around 39MB so 512DRAM would be enough. Error Message %AT-5-COMPATERR2: AppleTalk neighbor incompatibility;[atalk_net] has multiple zones Explanation Although this router has neighbors that require your internetwork to observe compatibility rules, AppleTalk has learned of a route with multiple No action required.

The specified peer notified this router of the change. This condition can cause inconsistencies for nodes in your internet. Recommended Action Call your technical support representative for assistance. http://www.techexams.net/forums/ccna-ccent/37790-2620xm-error-no-system-memory-detected.html Please help me !!!!!!!!!!

Error Message %CBUS-3-FDDIRSET: Interface [chars], Error ([hex]) [chars] -fddi_reset() %CBUS-3-FDDIRSETU: Unit [dec], Error ([hex]) [chars] - fddi_reset() Explanation A hardware device did not respond appropriately to a request. The MacIP server's configured IP address replaces X.X.X.X. If unexpected, verify that the MCI controller firmware for the interface specified in the error message is at level 1.7 or higher. Therefore, the route is marked as bad.

The router takes corrective action and continues. navigate here I may be wrong here, but shouldn't the router also enter setup mode if startup config is empty? Recommended Action Check for abnormally high CPU usage. Replace the malfunctioning device.

Recommended Action If the destination is valid, you must determine why the router does not know the route (that is, the neighboring router may be withholding information). navigate here If unexpected, correct the situation that caused the port to be disabled. Recommended Action Record the entire message and note any AppleTalk problems you experience. MacIP servers shut down in response to MacIP configuration changes or errors, or a change in the condition or configuration of an AppleTalk or IP interface for which the MacIP server

Recommended Action Informational message only. Cisco Support Community Directory Network Infrastructure WAN, Routing and Switching LAN, Switching and Routing Network Management Remote Access Optical Networking Getting Started with LANs IPv6 Integration and Transition EEM Scripting Other Recommended Action Call your technical support representative for assistance. Check This Out Recommended Action The system recovered by generating an error code to the requester Error Message %CBUS-3-FCICMDFAIL1: Controller [dec], cmd ([dec] 0x%-08x) failed (0x%-04x) count ([dec]) Explanation A command sent from the

Recommended Action Remove the route by reconfiguring the directly connected interface with which it is associated. Recommended Action Call your technical support representative for assistance. Error Message %CBUS-3-TESTFAIL: Unit [dec], failed [chars] test -interface disabled Explanation A hardware component failed an internal diagnostic test.

Recommended Action Informational message only.

Error Message %APPN-7-APPNSENDEVENT: [chars] Explanation A hardware or software error occurred. Quote jpnelson Junior Member Join Date Jun 2007 Location Mobile, Alabama Posts 4 Certifications A+ 12-09-200803:26 PM #11 And you got your money back!! Error Message %CBUS-3-CTRINIT: Unit [dec], CTR Initialization Failed - [char] Explanation The Token Ring interface failed its internal self-tests. Error Message %AT-6-DELROUTE: AppleTalk network deleted; [atalk_net] removed from routing table Explanation A route aged out of the AppleTalk internetwork.

Cisco Switch 2950 Ios Loading Problem … Error loading "" Interrupt within 5 seconds to abort boot process. An AppleTalk zone of the MacIP server replaces ZONE-NAME. Recommended Action Informational message only. http://buzzmeup.net/cisco-error/cisco-error-no-system-memory-detected.html Join Date Apr 2008 Posts 4,504 11-30-200803:24 PM #9 Originally Posted by mamono This is a guess, but sounds to me like it cannot access the NVRAM.

Restart the interfaces. Recommended Action The system recovered by generating an error code to the requester. Error Message %AT-5-NOSUCHROUTE: No such route [dec] Explanation The user tried to execute the EXEC commands show appletalk route or clear appletalk route with a nonexistent route. Recommended Action If either message recurs, call your technical support representative for assistance.

added this photo to their favorites. (26 months ago) Want to format your comment? Reset the cards. Recommended Action Call your technical support representative for assistance. Error Message %AT-3-DOMOVERFLOW: Remap Range OVERFLOW for [chars] Domain [dec] Explanation The remap range overflowed.

Recommended Action Informational message only.